/*! This file is auto-generated */ .wp-block-button__link{color:#fff;background-color:#32373c;border-radius:9999px;box-shadow:none;text-decoration:none;padding:calc(.667em + 2px) calc(1.333em + 2px);font-size:1.125em}.wp-block-file__button{background:#32373c;color:#fff;text-decoration:none} Q73P About one-third of the body of a... [FREE SOLUTION] | 91Ó°ÊÓ

91Ó°ÊÓ

About one-third of the body of a person floating in the Dead Sea will be above the waterline. Assuming that the human body density0.98g/cm3is find the density of the water in the Dead Sea. (Why is it so much greater than 1.0g/cm3?

Short Answer

Expert verified

The density of Dead Sea water is 1.5g/cm3.

The water of the dead is way saltier than the normal water. Therefore, the density of the water is high.

Step by step solution

01

Listing the given quantities.

The fraction of the body of a person floating in the Dead Sea is 13.

The density of the human body is,ÒÏp=0.98g/cm3.

02

Understanding the Archimedes principle.

By using the fraction of the body, which is inside the water, we can find out the ratio of the volume of the seawater displaced by the submerged body
(Vs)to the total volume of the person’s body(VÒÏ). Then using Archimedes’ principle, we can find ÒÏs.

Formula:

Fraction=1-VsVp

Fb=Msg

=ÒÏsVsg

Fg=Mpg

=ÒÏpVpg

03

(a) Calculation of density of Dead Sea water.

The fraction can be written as

Frac=Vp-VsVp

Frac=1-VsVp

13=1-VsVp

VsVp=1-13

VsVp=23

role="math" localid="1657552894793" Vs=23Vp(1)

Weight of the sea water displaced by the 13body.

Ws=Msg

Ws=ÒÏsVsg(2)

Buoyant force acting on the 1/3 body of a person is,

Fb=Mpg

role="math" localid="1657553033464" Fb=ÒÏpVpg(3)

According to Archimedes principle, we can equate equation (2)and(3)

ÒÏsVsg=ÒÏpVPg

ÒÏs=ÒÏpVpVs

Using equation (1),

ÒÏs=ÒÏpVp2Vp3

=ÒÏp32

=0.98g/cm3x32

=1.47g/cm3

Therefore, the density of Dead Sea water is 1.5g/cm3.

The density of the dead sea water is much higher than the normal water. The dead sea is located in the region where temperature is quite high and rainfall is quite low. Therefore, the rate of evaporation in the region is quite high. As a result, the water of the dead is way saltier than the normal water. Therefore, the density of the water is high.

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with 91Ó°ÊÓ!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

A small solid ball is released from rest while fully submerged in a liquid and then its kinetic energy is measured when it has moved 4.0cmin the liquid. Figure 14-40 gives the results after many liquids are used: The kinetic energy is plotted versus the liquid density, and sets the scale on the vertical axis. (a)What is the density?(b) What is the volume of the ball?

A very simplified schematic of the rain drainage system for a home is shown in Figure. Rain falling on the slanted roof runs off into gutters around the roof edge; it then drains through downspouts (only one is shown) into a main drainage pipe Mbelow the basement, which carries the water to an even larger pipe below the street. In Figure, a floor drain in the basement is also connected to drainage pipe M. Suppose the following apply: 1.The downspouts have height h1=11m, 2.the floor drain has heighth2=1.2m,3.pipe Mhas radius 3.0cm,4.the house side is width w=30mand front

length L=60m,5.all the water striking the roof goes through pipe M, 6.the initial speed of the water in a downspout is negligible, 7.the wind speed is negligible (the rain falls vertically). At what rainfall rate, in centimetres per hour, will water from pipe M reach the height of the floor drain and threaten to flood the basement?

In Figure, a spring of spring constant 3.00×104N/mis between a rigid beam and the output piston of a hydraulic lever. An empty container with negligible mass sits on the input piston. The input piston has area A1, and the output piston has area 18.0A1. Initially the spring is at its rest length. How many kilograms of sand must be (slowly) poured into the container to compress the spring by 5.00cm?

The tension in a string holding a solid block below the surface of a liquid (of density greater than the block) is T0when the container (Fig. 14-57) is at rest. When the container is given an upward acceleration of 0.250g, what multiple of T0 gives the tension in the string?

In an experiment, a rectangular block with height h is allowed to float in four separate liquids. In the first liquid, which is water, it floats fully submerged. In liquids A, B, and C, it floats with heights h/2,

2h/3, and h/4 above the liquid surface, respectively. What are the relative densities (the densities relative to that of water) of (a) A, (b) B, and (c) C?

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.